When we introduced the whole check for supported transports code, no one
noticed that it broke configuring all ostc's over bluetooth.
The configure code just used a placeholder model of OSTC 3 to get the
right backend code. With the new supported transports model it errored
out if you where trying to connect to a bluetooth enabled device, just
because the original OSTC 3's wasn't bluetooth enabled.
This switches the placeholder model over to a OSTC Plus which is both
bluetooth, serial and ble capable, so the code works again.
Signed-off-by: Anton Lundin <glance@acc.umu.se>
helpers.h included qthelper.h and all functions declared in helpers.h
were defined in qthelper.h. Therefore fold the former into the latter,
since the split seems completely arbitrary.
While doing so, change the return-type of get_dc_nichname from
"const QString" to "QString".
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
In firmware version 2.97 the setting 0x38, SETPOINT FALLBACK, has bin
obsoleted and we get a error when trying to write to it.
This removes this setting.
Signed-off-by: Anton Lundin <glance@acc.umu.se>
strdup(qPrintable(s)) and copy_string(qPrintable(s)) were such common
occurrences that they seem worthy of a short helper-function.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Replace constructs of the kind
s.toUtf8().data(),
s.toUtf8().constData(),
s.toLocal8Bit().data(),
s.toLocal8Bit.constData() or
qUtf8Printable(s)
by
qPrintable(s).
This is concise, consistent and - in principle - more performant than
the .data() versions.
Sadly, owing to a suboptimal implementation, qPrintable(s) currently
is a pessimization compared to s.toUtf8().data(). A fix is scheduled for
new Qt versions: https://codereview.qt-project.org/#/c/221331/
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
In the configure dive computer dialog change the order of the DCs
(all HW first, then Suunto) and correct the names of some HW DCs
(make them the same as in the "download from DC selection list").
Plus added the OSTC Plus to the list of supported DC.
Signed-off-by: Stefan Fuchs <sfuchs@gmx.de>
Currently, on Linux, after selecting a Bluetooth device the name of the
device is shown. On reopening the download dialog, on the other hand,
the address is shown. In the device selection dialog both are shown.
This patch changes the download dialog such that both, name and address,
are shown. The bulk of the patch introduces the name of the device in
the preferences and DCDeviceData. It has to be noted that DCDeviceData
is an encapsulation of the libdivecomputer device_data_t. Nevertheless,
the new Bluetooth-name field is, at the moment, not passed through to
libdivecomputer.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Correct spelling and typos in file filters.
Unify and translate file filter names.
Don't pass a file filter to a directory open dialog - not needed.
Signed-off-by: Stefan Fuchs <sfuchs@gmx.de>
QMap::operator[] creates a new default constructed entry in the map
if no entry with the given key exists. While not problematic (since
typically nullptrs are inserted) this is usually not what you want
for read access.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Way back in time this code was copied from downloadfromdcthread, so
de-duplicate and call that code instead.
Signed-off-by: Anton Lundin <glance@acc.umu.se>
Connect up all the settings that are the same, and remove those who are
not, and correct those who only are minor differences.
Signed-off-by: Anton Lundin <glance@acc.umu.se>
This is mostly copy-paste from the ostc3 case, but there are some minor
differences. Some minor things have different meaning, and there's a
slightly different command set, but I couldn't figure out a sane way of
joining them.
Signed-off-by: Anton Lundin <glance@acc.umu.se>
Wfloat-conversion enabled for C++ part of the code
Fix warnings raised by the flag using lrint
Original issue reported on the mailing list:
The ascent/descent rates are sometimes not what is expected.
E.g. setting the ascent rate to 10m/min results in an actual
ascent rate of 9m/min.
This is due to truncating the ascent rate preference,
then effectively rounding up the time to reach each stop to 2s intervals.
The result being that setting the ascent rate to 10m/min
results in 20s to ascend 3m (9m/min), when it should be exactly 18s.
Reported-by: John Smith <noseygit@hotmail.com>
Reported-by: Rick Walsh <rickmwalsh@gmail.com>
Signed-off-by: Jeremie Guichard <djebrest@gmail.com>
This is needed in the altitude pressure conversion as there
negative altitudes are possible (for diving in the netherlands
or the Dead Sea).
Signed-off-by: Robert C. Helling <helling@atdotde.de>
This adds support for notifying Ostc 4 users about new firmwares when
they download dives from their computers, gives them the option to
trigger the upgrade flow.
Signed-off-by: Anton Lundin <glance@acc.umu.se>
Use more general wording about bluetooth preparations, because nowadays
there are more computers than the Ostc Sport which use bluetooth.
Signed-off-by: Anton Lundin <glance@acc.umu.se>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
The list of OSTC devices have grown, and this updates our lists of for
which devices we should check for firmware updates.
Signed-off-by: Anton Lundin <glance@acc.umu.se>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
For some reason, the dive computer settings weren't in the
settings prefs. This moves it, makes the boilerplate on Settings
ObjectWrapper and make things compile.
Signed-off-by: Tomaz Canabrava <tomaz.canabrava@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Having subsurface-core as a directory name really messes with
autocomplete and is obviously redundant. Simmilarly, qt-mobile caused an
autocomplete conflict and also was inconsistent with the desktop-widget
name for the directory containing the "other" UI.
And while cleaning up the resulting change in the path name for include
files, I decided to clean up those even more to make them consistent
overall.
This could have been handled in more commits, but since this requires a
make clean before the build, it seemed more sensible to do it all in one.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
The unit for the depth parameters ain't meters, its 0.1 meters. This
caused the values stored to be out of range.
Signed-off-by: Anton Lundin <glance@acc.umu.se>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
This adds the configure parameters for safety stops on the hwOS(OSTC3)
and OSTC computers.
Signed-off-by: Anton Lundin <glance@acc.umu.se>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Since we have now destkop and mobile versions, 'qt-ui' was a very
poor name choice for a folder that contains only destkop-enabled
widgets.
Also, move the graphicsview-common.h/cpp to subsurface-core because
it doesn't depend on qgraphicsview, it merely implements all the
colors that we use throughout Subsurface, and we will use colors on both
desktop and mobile versions
Same thing applies for metrics.h/cpp
Signed-off-by: Tomaz Canabrava <tomaz.canabrava@intel.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
2015-10-30 10:36:49 -07:00
Renamed from qt-ui/configuredivecomputerdialog.cpp (Browse further)
