Not using lrint(f) when converting double/float to int
creates rounding errors.
This error was detected by TestParse::testParseDM4 failure
on Windows. It was creating rounding inconsistencies
on Linux too, see change in TestDiveDM4.xml.
Enable -Wfloat-conversion for gcc version greater than 4.9.0
Signed-off-by: Jeremie Guichard <djebrest@gmail.com>
This patch eliminates the difference between the saturation and
desaturation rates. This was probably once meant as a conservative
measure but the desaturation rate was increased rather than the
saturation rate (which is probably a typo, as reported by Stefan).
Since there is no good basis for this anyway, this patch sets
both factors to 1.0 (and if accepted the whole factor business
should be removed).
This makes our deco times slightly longer. But in the past,
we had introduced a 1.2% fudge factor in the critical radius
calculation to add conservatism and match the benchmark better.
Removing this fudge factor brings us close to the benchmarks.
Expected test values updated.
Reported-by: Stefan <sjti@gmx.net>
Signed-off-by: Robert C. Helling <helling@atdotde.de>
This resets the maximum crushing pressures and the maximal
ambient pressure between repetitive dives to prevent anomalies
that a dive produces a shorter deco when following another one
than without.
Reported-by: sfuchs@gmx.de
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
We have two prefernces determining the deco_mode (BUEHLMANN vs VPMB
vs RECREATIONAL): One for the planner (deco_mode) and one for
displaying dives (display_deco_mode). The former is set in the planner
settings while the latter is set in the preferences.
This patch clears up a confusion which of the two to use by introducing
a helper function that selects the correct variable.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
This patch fixes two bugs:
1) It first computes the effective gradient factors and then
composes the notes with the diveplan rather than the other way
around.
2) It does not try to fit a line through a single point.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
For each stop, this computes an effective gradient factor
that gives the same ceiling. Then, it does linear regression
to find values for GFlow and GFhigh that give a similar deco
profile.
Note that this optimises the average gradient factor. The
runtime however depends strongly at the gradient factor at
the last depth. So we don't necessarily to get the runtime
right.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Calculate gfline using the gradient factor that is set by the planner
preferences when in the planner, and by the general prefs when not in the
planner. This is achieved by doing the gradient factor calculation in dive.c,
where buehlmann_config is defined.
Previously, the gfline was calculated using the general preferences gfhigh and
gflow, even when in the planner.
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
... as those are needed for the heatmap and not only
for Buehlmann ceilings.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Separate the VPM-B conservatism preference into diveplan.vpmb_conservatism for
planning dives and prefs.vpmb_conservatism for profile ceiling display of
saved dives.
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
... and not just for Buehlmann. This makes the saturation
graphs meaningful for VPM-B.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Change runtime table string from ZHL-16B to ZHL-16C to reflect he fact
that we use 5min as half-time for the fastest compartment rather than
4min.
Further more trade pow(2.0, ...) for exp().
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Having subsurface-core as a directory name really messes with
autocomplete and is obviously redundant. Simmilarly, qt-mobile caused an
autocomplete conflict and also was inconsistent with the desktop-widget
name for the directory containing the "other" UI.
And while cleaning up the resulting change in the path name for include
files, I decided to clean up those even more to make them consistent
overall.
This could have been handled in more commits, but since this requires a
make clean before the build, it seemed more sensible to do it all in one.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
