I'm sure this bug has heen here forever, but the CNS clock is
not very relevant for most divers, and even some technical divers
do not care about this value.
However, doing long decompression dives, the value can easily
grow over 100%, and a lot further. For example, the OSTC computers
use 2 bytes to store the CNS value in the profile data, and I
have multiple dives in my logbook going way over 255%.
This all said. Just store the CNS value in an unsigned 16 bit.
Signed-off-by: Jan Mulder <jlmulder@xs4all.nl>
Commit d15779a calculates final stop based on stoplevels[2], but if final stop
is 6m/20ft, we should use stoplevels[3]. This fixes it.
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
Some messed up logic was producing negative deco_time values for some no-deco dives. The CVA wouldn't converge and unrealistic VPMB ceilings were displayed in the profile. This fixes it.
See #762
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
We calculate tts every 30s, not every sample. Consider that when determining
the time that the ceiling would have cleared if it's after the surfacing time.
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
This makes the calculations in profile.c a little simpler, especially now we
adopt consistent final ascent rate to determine deco_time since d15779a27
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
If we consider the actual time to ascend from the final stop when calculating
deco_time, then slowing the final ascent can lead to the final stop being
extended, which is completely nonsensical. For consistency with the original
VPMB implementation, we can't ignore the final ascent time completely, but if
we assume it is always the same (take default ascent rate of 9m/min) then
slower the final ascent won't lead to a longer final stop.
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
As it is not possible to delete dive sites from the logbook, we
need to make sure that we never save sites that are not tied to
any dive. With this change, unused site that are currently in
the logbook will also be removed, so it will also clear up
(wrong) historical data.
Supposed to fix#786
Signed-off-by: Jan Mulder <jlmulder@xs4all.nl>
A change of the font_size in preferences ended up in the wrong
preferences group (the GeneralSettings group), appearing to the
user as a non-saved preference. Fix is simple. Just set the
the correct group before saving a change in font_size.
Fixes: #780
Signed-off-by: Jan Mulder <jlmulder@xs4all.nl>
Recognize Aladin as the Bluetooth name of the Scubapro Aladin Sport
Matrix. Note that the Scubapro Aladin H Matrix most likely also
identifies itself using this BT name. But it probably uses the same
BT protocol (i.e. the G2 protocol) and therefore this should not pose
a problem. Ultimately a common name should be found.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Remove unused variables o2time and breaktime or convert into boolean.
Never consider minimum gas switch time when switching to o2.
Reflect this behavior also in the UI.
Signed-off-by: Stefan Fuchs <sfuchs@gmx.de>
QMap::operator[] creates a new default constructed entry in the map
if no entry with the given key exists. While not problematic (since
typically nullptrs are inserted) this is usually not what you want
for read access.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Currently one has to explicitly use --win32console and/or
--win32log to enable a dedicated console (a console window
that opens next to the Subsurface window) or to enable file
logging on Win32.
This patch makes the following changes:
- removes the --win32* command line arguments
- removes the dedicated console window support
- if the app starts from a shortcut and not from a console, always
redirect stderr and stdout to _err & _out log files
- if the app starts from a console redirect stderr and stdout to that
console
Signed-off-by: Lubomir I. Ivanov <neolit123@gmail.com>
1) Destroy QLowEnergyService objects in destructor of BLEObject.
2) Let BLE object take ownership of the controller so that the
latter can be destroyed in the destructor of the former. This
introduces a certain ownership subtlety, which could be solved by
allocating the controller object in the BLE object. But let's
first do the less intrusive thing.
3) Destroy the BLE object for two error conditions.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
When planning a VPM-B dive, the "deco time" ends at surfacing, which is after
ascending after a full-minute deco stop is complete, after ceiling clears. We
should take this into account when calculating the ceiling outside of the
planner.
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
This corrects the issue where the displayed ceiling in the profile was
"broken" by the planner, especially for shorter and shallower dives.
Also fixes issue outside of planner where the deepest VPM-B ceiling was shown
too early, messing up the deco_time calculation.
VPM-B plans respond to change in O2% in gas as expected (in my testing)
Fixes: #630
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
If we consumed 0l/0bar in total from a cylinder there is no need to also
state that we consumed 0l/0bar during ascend.
Signed-off-by: Stefan Fuchs <sfuchs@gmx.de>
Because now we are trying to open a URL as if it was a local file.
Again, the goal is to accelerated debugging if things go wrong.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
This is rather fragile code, and the capitalization of the error message
in libgit2 changed at some point. But commit 794739b4c0 ("strstr is a
case sensitive compare") didn't really fix the problem - as it broke
that same check for older libgit2 versions.
Instead use our new helper function to make it work with libgit2 old and
new.
Also, add some more error output so the next time we run into this it's
more obvious what broke and where.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
That's not a standard functions, so let's just build it. This is not
the most efficient way to write it, but it will do.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
This string is substituted with the runtime increments derived of slight
variations in depth or bottom time in:
diveplannermodel.cpp:1058:
displayed_dive.notes = strdup(notes.replace("VARIATIONS", QString(buf)).toUtf8().data());
Translating it avoids substitution and we just get the translated
string.
Signed-off-by: Salvador Cuñat <salvador.cunat@gmail.com>
Fixes minor interface inconsistency: After a failed download, the
error message was also shown on subsequent successful downloads.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Otherwise the following call to do_git_save will potentially have incorrect information
about the cache validity of the dives in the divelist.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Inexplicably, commit 8b7427c56d ("Move CloudStorage out of the widgets")
didn't just move the code but added a local member 'verbose' that hides
our global variable...
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
This became rather obvious with the change to immediately show errors.
The commit also fixes a small memory leak.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
The pressure information of cylinder should be kept intact when
copy-pasting other cylinder related information from other dive.
According to Dirk, the gas mix is wanted to be changed as technical
divers might have always the same multiple cylinders and wish to copy
the gasmix information over.
Fixes#689
Signed-off-by: Miika Turkia <miika.turkia@gmail.com>
This line:
dc = &dive->dc
can SIGSEGV for a NULL 'dive' pointer.
return NULL if 'dive' is NULL.
Also handle NULL 'dc' in get_gasmix() and set 'ev' to NULL.
Signed-off-by: Lubomir I. Ivanov <neolit123@gmail.com>
current_dc is a macro that determines the dive computer
based on the current dive number. When the planner is started
from an emtpy dive list, the dive number ends up being -1 and
that doesn't produce a valid dive computer. Use the divecomputer
of the displayed_dive instead. This is done via a macro that
can also be used in two other places. Without this patch, the
planner crashed when called on an empty dive list.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Identify previous dives for CNS calculation in a similar way as it
is done for previous dives for deco calculation.
This is done to identify the previous dives dynamically when moving
around date/time of a dive in the planner.
Signed-off-by: Stefan Fuchs <sfuchs@gmx.de>
