Most (all?) BLE dive computers actually don't need to be paired, and some
apparently can't be paired. So let's not enforce that.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
A regular expression was generated and then copied twice without
apparent reason. Remove these copies.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
By default we'll only show devices that we believe to be dive computers,
but the user can override that with the recently introduced check box.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
In the remoteDeviceScanFinished slot, the old code called into
the deviceDiscoveryError() in case the device discovery agent
had the error flag set. This is not necessary, since the agent
will send an error signal in such a case.
For Qt's device discovery agent, the whole check-for-error is
unnecessary, as the documentation states:
"The signal is not going to be emitted if the device discovery
finishes with an error."
But for the homebrew WinBluetoothDeviceDiscoveryAgent, which
derives from QThread, both an error() *and* a finished()
signal will be sent. Therefore keep the test, but don't call
into the slot twice.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Each callsite of saveBtDeviceInfo() has a QString, which is converted
to a C-string, passed and immediately converted back. Remove these
conversions by taking a reference to QString directly.
getBtDeviceInfo() is not as clear. Here, the callsite has a C-string
handed down from libdivecomputer. Nevertheless, pass a reference of
QString here as well. Firstly, for reasons of symmetry. Secondly,
to avoid multiple conversions in the getBtDeviceInfo() functions.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
As far as I know, Qt's emit is defined to nothing.
Thus, the construct "emit(lastError);" is compiled to
"(lastError);", which is a no-op.
Obviously "emit error(lastError)" was meant.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Some BT devices support both, classical and LE, modes. Users could
choose either by prepending or removing "LE:" in the device address
field. After commit d23bd46a1b, the
device field is always disabled in Bluetooth mode.
Therefore, add a mode combo box to the Bluetooth device selection
dialog. In the default mode (auto), the old code path (based on
the Qt device flags) is used. The two other modes (force LE, force
classical) allow the user to force the preferred behavior.
This feature is meant as a stop-gap measure until a more refined
transport choice is implemented. Therefore, the value of the new
combo box is not saved in the settings, to avoid cluttering of
the preferences with soon to be obsolete entries.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Currently, on Linux, after selecting a Bluetooth device the name of the
device is shown. On reopening the download dialog, on the other hand,
the address is shown. In the device selection dialog both are shown.
This patch changes the download dialog such that both, name and address,
are shown. The bulk of the patch introduces the name of the device in
the preferences and DCDeviceData. It has to be noted that DCDeviceData
is an encapsulation of the libdivecomputer device_data_t. Nevertheless,
the new Bluetooth-name field is, at the moment, not passed through to
libdivecomputer.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Since the QSharedPointer is never passed or copied, reference counting
is certainly not needed.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
This fixes two problems:
1) Using the keybord or clicking below the list and moving the mouse
up while holding the mouse button did not properly update the status
message and the save button. For example, one could save with a non-
paired device selected.
2) The code assumed that a device is selected if the save button is
active, but the save button was not disabled on scan. Thus, one could
provoke a crash by selecting an item, scanning and then pressing save.
This problem is fixed indirectly, because the save button is now always
disabled if the selection is cleared.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
This seems a bit odd, but it actually has three different reasons for it:
- It's a visual indication of BT LE mode for users
- the rfcomm code only works with legacy BT support, and if we scan a
device that only does LE, we want the custom serial code to instead
automatically fall back on a "emulate serial over LE packets" model.
- we want rfcomm to remain the default for devices that do both legacy
BT _and_ LE, but we want people to have the ability to override the
choice manually. They can now do so by just editing the address
field and adding the "LE:" prefix manually, and it automatically gets
saved for next time.
So while a bit hacky, it's actually a very convenient model that not
only works automatically, but allows the manual override.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Since we have now destkop and mobile versions, 'qt-ui' was a very
poor name choice for a folder that contains only destkop-enabled
widgets.
Also, move the graphicsview-common.h/cpp to subsurface-core because
it doesn't depend on qgraphicsview, it merely implements all the
colors that we use throughout Subsurface, and we will use colors on both
desktop and mobile versions
Same thing applies for metrics.h/cpp
Signed-off-by: Tomaz Canabrava <tomaz.canabrava@intel.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
2015-10-30 10:36:49 -07:00
Renamed from qt-ui/btdeviceselectiondialog.cpp (Browse further)
