This is another attept at the problem if identifying a potentially
user supplied text in the dive notes upon replannig a dive.
It gets rid of the user visable position markers (*!* and ***) and
cirumvents problems with mark-up by first converting the old notes
to plan text (assuming that user only enters plain text in the notes
field as we do in other places as well). Then the automatically added
part is identified by locating the disclaimer in the text (if the user
edited/delted the disclaimer or changed langue in between it is her
problem to manually delete the old plan).
Everything from the disclaimer on is deleted and replaced by the new plan.
If the disclaimer is not found, the new plan is appended to the old notes.
This way we make sure no information gets automatically deleted.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
When replanning a dive, the setpoint information from the profile waypoints
were reset to 0, resulting in a dive that has a dive mode of CCR, but only with
OC legs in the profile. This is just wrong, and is corrected here. Notice
that there is no averaging involved (in the reduction of a replanned real
dive that has more than 100 waypoints) as is done for depth. This is just
fine for setpoint data.
Signed-off-by: Jan Mulder <jlmulder@xs4all.nl>
New strategy to identify old planner output in notes when
replanning a dive: Text anchors ("*!*" and "***") added for planner output
For backwards compatibility: If there is no anchor but an old table
delete everything.
Signed-off-by: Stefan Fuchs <sfuchs@gmx.de>
Don't add the last stop with addstop for correcting the lenght
of the dive if planner generated points can be removed when replanning.
Otherwise this will not be deleted when replanning a dive.
Signed-off-by: Stefan Fuchs <sfuchs@gmx.de>
Upon replanning a dive, we want to delete the old
dive plan in the notes and replace it with the actual.
This fixes a problem when we failed to detect the old plan due
to the deco model name appearing in the disclaimer that was used
as a marker for the notes.
This patch also adds translation markers for the deco model name strings..
Fixes#285
Signed-off-by: Robert C. Helling <helling@atdotde.de>
... for consistency, while we are at it.
There are still some internal depth variables which are ints
somebody might take a go at those.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
This is needed in the altitude pressure conversion as there
negative altitudes are possible (for diving in the netherlands
or the Dead Sea).
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Add minimum gas calculation to planner output.
Add the two UI parameters prefs.sacfactor and prefs.problemsolvingtime.
Connect UI signals and slots for recalculation of diveplan.
Disable minimum gas calculation if there was already a warning before.
If minimum gas result is larger then cylinder start pressure give warning message instead of result.
Add line break before pO2 warnings but only if warnings exist.
Signed-off-by: Joachim Ritter <jritter@bitsenke.de>
Signed-off-by: Stefan Fuchs <sfuchs@gmx.de>
Using gcc option "-Wfloat-conversion" is useful to catch
potential conversion errors (where lrint should be used).
rint returns double and still raises the same warning,
this is why this change updates all rint calls to lrint.
In few places, where input type is a float, corresponding
lrinf is used.
Signed-off-by: Jeremie Guichard <djebrest@gmail.com>
Use the function in every place instead of once using it and once copying the code again.
No functional change.
Signed-off-by: Stefan Fuchs <sfuchs@gmx.de>
It's not too clever to give 0 a special meaning (as here:
use same gas as for previous leg) when 0 is a legitimate
value.
This should solve Willem's gas disappearance problem when
reediting a dive in the planner.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
In the cylinder table, the last column ("use") always showed
OC-GAS. Editing was enabled, but the user had to guess to enter
a small integer meaning dilluent or CCR oxygen cylingder. I guess,
nobody has ever done that.
This patch makes this column clickable. A click toggles if the cylinder
is used for planning or not. This wait it is much easier to investigate
the consequences of gas loss on a plan.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Gas switches appear as special samples with zero or one second duration.
Those can be confusing when they appear as zero duration in the dive plan
when replanning, so better suppress theose.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
By using SettingsObjectWrapper, the planner settings can be saved and restored
correctly
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
This is to avoid confusion with planner.display_deco_mode.
When accessing the "current deco mode" use the decoMode()
helper function.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
This can happen when the user asks to replan a dive that
was imported from CSV.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Call GasSelectionModel::instance()->repopulate() when creating the initial
simple dive. Without this call, the gas selection dropdown list does not work
in the DivePLannerPointsModel table until the cylinders table has been edited.
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Separate the VPM-B conservatism preference into diveplan.vpmb_conservatism for
planning dives and prefs.vpmb_conservatism for profile ceiling display of
saved dives.
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Subsurface uses "local time" which in particular means we never
display time zone information to the user. The user (and our file
format) only sees times like 5pm or 17:00. A better name than
local time (which could mean "local at the dive spot) would
be "watch time", the time displayed by the diver's watch when
she entered the water.
Internally, we store times as time_t, seconds since Jan 1 1970 0:00
UTC. Our convention for conversion between 5pm and time_t as always
been to treat 5pm as if it were UTC.
Then confusion arose since Qt's QDateTime (which is tied to UI elements
like QTimeEdit and similar) is time zone aware and by default assumes
the system time zone. So when we set a QDateTime to 5pm and then later
convert it to time_t we have to take care about the difference between
UTC and the system time zone.
This patch unifies our solution to this problem: With it, we set all
QDateTime's time zone to UTC. This means we don't have to correct for
a time zone anymore when converting to time_t (note, however, the
signedness issue: Qt's idea of time_t is broken since it assumes it
to be unsigned thus not allowing for dates before 1970. Better use the
millisecont variants).
We only need to be careful about time zones when using the current time.
With this convention, when assigning the current time to a QDateTime, we
need to shift for the time zone since its value in UTC should actually be
the watch time of the user who is most likely used to the system time zone.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Commit b1ed04a means that DivePlannerPointsModel::rememberTanks() and related
functions and variables are no longer required
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Add option to calculate the best mix portion of O2 and He for the dive's max
depth if the user enters * in the MOD and MND cylinder fields. Gas portions
are automatically recalculated if the max depth of the dive changes.
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Determining the correct cylinder index from a known gas mix can be
complicated, but it is trivial to look up the gasmix from the cylinder_t
structure.
It makes sense to remember which cylinder is being used. This simplifies
handling changing a cylinder's gas mix, either directly by the user, or
indirectly in the planner. It also permits tracking of multiple cylinders of
the same mix, e.g. independent twins / sidemount.
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Having subsurface-core as a directory name really messes with
autocomplete and is obviously redundant. Simmilarly, qt-mobile caused an
autocomplete conflict and also was inconsistent with the desktop-widget
name for the directory containing the "other" UI.
And while cleaning up the resulting change in the path name for include
files, I decided to clean up those even more to make them consistent
overall.
This could have been handled in more commits, but since this requires a
make clean before the build, it seemed more sensible to do it all in one.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
In the planner, for recreational mode, there is a setting indicating
the pressure at which the diver should be back at the surface. This
pressure was hardcoded to bar.
Fixes#1027
[Dirk Hohndel: small modifications, more reasonable step for psi,
more reasonable maxima]
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Then the user can select the two copies and merge them as two different
computers. Without this, the selection could is screwd up and there
is no option to merge in the context menu.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Apparently, it can happen that the default cylinder is not set
even though same_string(prefs.default_cylinder, "") is false.
Then we fall back to the 11.1l air cylinder.
This should silence a warnign about "Too many gases".
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
void DivePlannerPointsModel::setupCylinders() in diveplannermodel.cpp
handles setting up cylinders for the planner. If there is a current
dive, cylinders form that dive are copied. Otherwise the default
cylinder is added and lacking that a standard size cylinder.
If the current dive does not have any cylinders, we could end up
without cylinders. This patch adds a test for this case and delegates
to the other two sources of a cylinder in that case.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
I have manually added dives from an ancient version of Subsurface.
Trying to edit these caused Subsurface to crash due to comparison of
string of dc.model that did not exist (to a static string). And further
down the execution path we were crashing as there were no samples
associated with the dive.
See #941
Signed-off-by: Miika Turkia <miika.turkia@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Spell Setpoint without space in user visable strings.
Explain authorized_paired.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Conservatism level can now be changed from gui, is saved in settings.
Also way of disabling the planner settings in the ui was improved
to support more deco models and be called at the widget creation.
Signed-off-by: Jan Darowski <jan.darowski@gmail.com>
When VPM-B is the choosen deco algorithm changing,
GF low and high have no effect. So lets disable them similar to what we do
for recreational mode.
Signed-off-by: Joakim Bygdell <j.bygdell@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
