On selection change, pass down selection (including current
dive and dc) to the tab widgets. Ultimately, this should
remove access to global variables. A number of new accesses
are marked as TODO. They shall be removed in due course.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The signals/slot names for dive selection changes were a mess.
Unify on divesSelected(). Firstly, selectionChanged() is a Qt
thing. Secondly, it is consistent with tripSelected().
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
This was very weird: a setSelection() call was always followed
by a selectionChanged() call, though sometimes in convoluted
ways. Notably, the formed was called by the DiveListView, the
lattern then by the MainWindow.
Let's just merge these two functions.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
In DiveListView user actions (select-all, key-press,
mouse-release) were intercepted to send the selection-changed
signal if the selection changed.
However, with the recent cleanups, this can be done
directly from selectionChanged(), since in all cases (at
least the ones I tested), the part of the function that
is responsible for manual selection changes is called
only once.
This avoids quite some complex code flow.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
When manually selecting a trip, the selectionChanged()
virtual function was manually selecting the dives of the
trip and thus ultimately recurse into itself.
So far this seems to work OK, but better to avoid this
recursion by setting the programmaticalSelectionChange
flag.
I'd like to send the selection-changed signal directly
from selectionChanged() and this recursion would lead
to double signals.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The trip selection code was an awkward layering violation.
Whereas dive selections due to dive undo-commands trickled
down via DiveTripModel-->MultiFilterSortModel-->DiveListView,
for trip editing, the DiveListView directly intercepted the
TripEdited signal.
Instead, mimic the dive-selection code. This is a bit longer
but more consistent and logical. The undo/redo of trip changes
is now also a "programmatical" change of the selection.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
After sending a selection-change signal, there follows a current
dive changed signal. Combine these two into a single signal, since
usually the current dive is changed when the selection is changed.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Instead of accessing the global dc_number from the
DivePlannerPointsModel and the CylinderModel, pass them
in the respective initialization functions.
The dc_number global might not make sense on mobile.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Each of these calls recalculates the current dive and divecomputer.
Instead, collect the dives to be selected/deselected and (de)select
them at once.
This needs some code refactoring in the core, because we need a
function that
1) doesn't send a signal by itself.
2) doesn't clear the trip-selection.
This contains some reorganization of the selection functions
signatures: The filter code is the only caller that keeps the
selected dive and the only caller that cares about whether the
current dive changed. So let only the function that keeps the
selected dive return whether the current dive changed.
It's all very fragile.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
This tries to encapsulate the management of the current dive and
divecomputer in the selection code. The current dive is alreay
set by setSelection(). Add a new parameter to also set the
current divecomputer. If -1 is passed, then the current
computer number is remained. This will allow us to audit the code.
Because for now, the whole "current dive computer" thing seems
to be ill-defined.
This fixes a bug: the dive-computer number wasn't validated
when making a new dive the current dive. The new code has some
drawbacks though: when selecting a whole trip, the validation
will be called for all dives in the trip and thus the dive computer
number will depend on the dive with the lowest amount of dive
computers in the trip. This will need to be fixed.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The parser API was very annoying, as a number of tables
to-be-filled were passed in as pointers. The goal of this
commit is to collect all these tables in a single struct.
This should make it (more or less) clear what is actually
written into the divelog files.
Moreover, it should now be rather easy to search for
instances, where the global logfile is accessed (and it
turns out that there are many!).
The divelog struct does not contain the tables as substructs,
but only collects pointers. The idea is that the "divelog.h"
file can be included without all the other files describing
the numerous tables.
To make it easier to use from C++ parts of the code, the
struct implements a constructor and a destructor. Sadly,
we can't use smart pointers, since the pointers are accessed
from C code. Therfore the constructor and destructor are
quite complex.
The whole commit is large, but was mostly an automatic
conversion.
One oddity of note: the divelog structure also contains
the "autogroup" flag, since that is saved in the divelog.
This actually fixes a bug: Before, when importing dives
from a different log, the autogroup flag was overwritten.
This was probably not intended and does not happen anymore.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Strangely enough, half of the infrastructure was
already there, it just wasn't hooked up to a UI
element
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Fix a bug causing the bluetooth address not being used when downloading
from a 'remembered' dive computer if the device selection is populated.
This specifically excludes MacOS, as 'remembering' bluetooth connections
does not seem to be working there as per
https://github.com/subsurface/subsurface/pull/2158#issuecomment-508933672.
I am not super sure why we are _not_ trying to use the 'remembered'
device if the device selection is populated (`ui.device->currentIndex()
== -1`) - maybe this should be clarified in a comment?
Signed-off-by: Michael Keller <github@ike.ch>
Make the time edit respect the configured time format. Also make the
date and time format change when the preferences are changed.
Fixes#3849.
Signed-off-by: Michael Keller <github@ike.ch>
In order to support development of the open source firmware of the
OSTC4.
Requires changes in libdivecomputer.
Signed-off-by: Michael Keller <github@ike.ch>
Fix a bug causing the wrong units (m) to be shown on the Dive site
management view if imperial units are as the system default.
Signed-off-by: Michael Keller <github@ike.ch>
Disable the 'search dive computer' ([...]]) button in the 'Import from
dive computer' window if searching is not supported by the currently
selected vendor.
Signed-off-by: Michael Keller <github@ike.ch>
Use the drop down for editing the tank use in the gas list in both the
equipment tab and the dive planner.
The tank use column is now available in the equipment tab for all dives
and not just CCR dives, as 'not used' is a valid entry in both cases.
However, if the current dive is an OC dive, only 'OC-gas' and 'not used' are
shown.
There still seems to be a problem that in some cases, when opening the
planner after selecting an existing CCR dive the drop down in the
planner does not list CCR gas uses - for some reason `displayed_dive`
does not seem to be updated correctly on opening of the planner. But I have not been able to
reproduce this consistently, and changing 'Dive mode' fixes this.
Signed-off-by: Michael Keller <github@ike.ch>
Clarified the message that is shown when a newer dive computer firmware
version is available, informing the user that
using an older firmware version may result in problems when using
Subsurface, as discussed in #3568.
This is currently only supported for Heinrichs-Weikamp dive computers.
Signed-off-by: Michael Keller <github@ike.ch>
The Heinrichs Weikamp OSTC4 introduced an additional
'Cave' brightness level that is dimmer than all existing ones.
Signed-off-by: Michael Keller <github@ike.ch>
Users report that the ShiftTimesDialog does not work on Mac and
Windows. Apparently, get_first_selected_dive returns NULL, which
should not be possible because the dialog is only created when
dives are selected. Very omninous.
Get the selected dives in the caller and pass them down. This
bug at least should not happen anylonger. Perhaps now the
dialog does not show at all, but that will narrow down the
root cause of the problem.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
This include prevented the statistics from loading for me on Qt6.
And it appears to be unnecessary.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
When switching from "empty mode" (i.e. the subsurface logo is shown,
because no dive is selected), the profile is first shown by switching
to the appropriate tab and then plotted. However, the showing might
lead to a resize event and then to a crash with owing to stale dive
data. Therefore, reverse that.
Note that I never could reproduce that.
Reported-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
In the printing-template code, we loop through a vector and
then determine the index of the current element by searching
the vector. This irks me.
Since looping over a collection with an index is a rather
common theme, implement an enumerating iterator that can
be used as in:
for (auto [idx, item]: enumerated_range(v)) {
...
}
For now, use it for the above vexing case. Convert other
iterations of this theme later.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
For reasons of symmetry (there is a is_manually_added_dc()
function), create a make_manually_added_dc() function.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
This causes UI confusion. Notably we go into edit mode and
reduce the number of samples, leading to loss of information.
If someone really manually adds a dive with more than 50
samples, they should still be able to explicitly open the
dive in the planner.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
This got broken in commit 7417f865cd ("cleanup: un-singletonize
ShiftTimesDialog") and no one ever noticed.
We need to intitialize the when variable and set up the initial texts in
order for the time shift dialog to show the correct information. Doing
this in the ButtonClicked member (right before the dialog is destroyed)
makes absolutely no sense.
Fixes#3535
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
The dive-site editing can be reached from two states: from the
dive view and the dive list view. It always jumped back to
the dive view.
Therefore, remember the state. Use a stack-like structure, so
that the feature can be used for the dive-site view as well.
This is a bit inconsistent, because for example the statistics
view does not remember the previous state and allows a direct
jump to a different state. That should be fixed at some point.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
This used to be one of the tab-widgets, which was illogical
and caused confusion. Notably, erroneously clicking on the
tab header led to a reset of the dive selection.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Owing to bit-rot, the extradata tab was not disabled if no dive
is selected. The reason was that there was an additional tab
(dive-computers) that should not be disabled. However that
tab was removed and now the extradata tab was not disabled.
Fix this, but note that there is another of these 'parasitic'
tabs, that should be removed, namely the dive-site tab.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The map listens to the reset signal by itself.
This avoids double reload of the map on open/close.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The get_minutes() function formats a time as m:ss
and returns a static C-string. Since all callers are
C++ anyway and transform directly into QString, let us
move this to the other string formatting function.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Also allow editing sensor on a cylinder with already attached sensor.
This will swap the sensor data with the cylinder that it is taking the
sensor data from, removing the need for adding an extra temporary
cylinder when swapping two sensors.
Signed-off-by: Michael Andreen <michael@andreen.dev>
No reason to keep this as a macro - a function is easier to
read, type safe and easier to debug. Moreover, give it the
more appropriate name "nearly_equal()". After all, it precisely
does NOT check floating points for equality.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The FP_IS_SAME macro uses a relative precision to compare
floating points. This fails when comparing to 0. Therefore,
use an absolute precision in this case. Implement as an
inline function.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
