This changes the algorithm that picks the sac color to consider
+/- 1 l/min to be the same color (before the color changed every
time you crossed above or below the average which looked silly with
our synthetic "constant sac" values as those are discrete and oscilate
around the average.
This also changes the order in which things are drawn so so that the
pressure plot goes over the depth profile plot (so the red shading of the
dive no longer changes the color of the tank pressure plot).
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Use rgb_t for the sac colors, create a new set_source_rgb_struct function
and use that for the velocity values (in the depth plot) as well.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Linus suggested that instead of using absolute SAC values to base the
color on (which forced us to pre-define which SAC rates are green and
which are red) we should color the tank pressure plot relative to the avg
SAC rate of that dive - which I think makes the coloring much more useful
to spot when on your dive you were doing well and when you were not.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Similar to color indicating vertical speed in the profile plot we now use
color in the tank pressure plot to indicate current SAC rate.
We use a 45 sec sliding window to make sure we cover at least two breaths
for each current SAC sample to avoid artificial oscillation based on
breathing rhythm for corputers with high sample resolution.
Not sure about the color coding that I'm using right now - it's green-ish
for SAC rates under 15l/min ~= .55cuft/min and turns yellow and red as you
go higher. That seems to work well for me, but for other divers this may
be way off (or at least not as useful). Maybe this should be configurable?
This is a lot more diver specific than the vertical velocity where there
are clear recommendations based on safety considerations on what is good
and bad.
As a side effect, this removes the color coding that showed you whether
you were looking at pressure data from samples (green) vs. interpolated
pressure data (yellow). Not sure if people really want to see that. We
might be able to indicate this differently (I am thinking different line
width or transparency or something along those line)
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Some dive computers randomly drop samples. That was no problem unless it
was the LAST sample. We work around that now
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
.. and fix the maxpressure to actually look at *all* the cylinders, so
that if you don't have sample data, but rely onmanually set cylinder
pressures, it now really is the max of all the cylinders.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We no longer look at the start and end pressure for a tank, if the tank
has valid pressure data in its samples (which makes sense). Sadly that
breaks the current pressure interpolation code. With this patch most of
those problems should be fixed.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
- make the text a lighter color so it stands out more
- change the heuristic when we print text to include both relative change
in temperature and time since the last text was printed
- print the first temperature we encounter
- allow an ending temperature to be printed if the last printed
temperature was before the 75% mark of the dive
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
I thought we had fixed this before - but I guess it got broken again
somewhere. We now make sure that the plot_info ends on an entry with
depth 0.
Added test14 to verify the fix.
Also fixed cut'n'paste errors in a few test dive files.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
In some situations we could end up with no sample pressure and no
interpolated pressure at time = 0. This is now fixed.
Fix notes in test dive the exposed the issue.
Also change the code in create_plot_info to keep the number of samples and
the number of corresponding pi entries in separate variables. This avoids
future changes from breaking if they assume they can access
dive->sample[nr_samples - 1] (which is a reasonable assumption to make).
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
This was exposed by the test dives, but it shows up in small ways with
real dives from some dive computers like the Suunto Vyper Air.
We now insert synthetic plot_info entries that match the gas change event;
to make this look smoother we insert either two events (one for the old
tank, one a second later for the new tank) if there is no sample at the
time of the event, or one additional event (and move the real sample back
by one second) if there is a sample at the time of the event.
This does expose another issue with some dives from Linus' computer where
the pressure in the samples dips below the end pressure noted for the tank
- which creates an odd "yellow up-tick" at the end of using the first tank
in the plot. Maybe we should not insert a synthetic "last of old tank"
event if we have a sample with valid pressure in the last NN seconds
before the gas change?
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
If we have more than four identical depth readings, the old code would see
those as local maxima and minima and print spurious depth values in the
profile plot.
Yes, in real sample data identical readings won't happen - but in
synthetic data they can and there this looks really bogus.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Finally getting more consistent overall in how we convert between the
different units and how we decide which units to display.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Designed along the lines of get_depth_units - except we don't define a
specific number of digits to show.
Use this in the one spot we need it right now in profile.c
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
We used to have the dive plot have two "filler" entries at the beginning
and the end, and indeed that is how they are allocated. However, we fix
up "pi->nr" later to be "lastindex+1", where "lastindex" is the index of
the time we surface.
So when we loop over the plot entries, we actually need to loop all the
way to the end: use "i < pi->nr" instead of "i < pi->nr-2".
We still do have the two extra filler entries at the beginning, though.
So depending on the loop, we might want to start at entry 2.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Right now it just plots something ridiculous, the code is really just
meant to be an example. We migth be able to plot a traditional
staircase plot and make it look somewhat saner by taking mean depth into
account (if it exists).
Right now it just plots a (skewed) rectangular dive profile using the
max depth and total time. Which is obviously insane.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When creating the plot_info, the 'entry' variable pointing to the last
plot_info data was not initialized (because there was no data to fill
in), and was then incorrectly used to fill in the last tank pressure.
We also used to look at 'dive->sample[0].cylinderindex' even if no
sample[0] necessarily existed.
Reported-by: Miika Turkia <miika.turkia@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Right now they are displayed in one hbox which doesn't work if you have
many events - but the code itself works and correctly toggles the events
on and off.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
We don't have a way to actually configure this in the app, yet, but
toggling the bits in the debugger shows that this works, so commit this
code now.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
First step to being able to filter the events that we display in the
profile. We could (in theory) walk all the dives in the divelist when we
need this data, but it seems much more convenient to have them in an array
in one place.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
* 'ui' of git://github.com/dirkhh/subsurface:
Disable sorting by dive number
Fix oversight in preference implementation
Make columns for temperature, cylinder, and nitrox optional
Show dive number in dive list
Improve time marker handling and add printing of some time labels
We now draw time markers at most every 5 min, but no more than 12 markers.
For convenience we do 5, 10, 15 or 30 min intervals.
This allows for 6h dives - enough (I hope) for even the craziest divers -
but just in case, for those 8h depth-record-breaking dives, we double the
interval if this still doesn't get us to 12 or fewer time markers.
We label the first and then every other time marker with the minute text.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Dirk wrote the multi-cylinder support assuming that the dive computer
always gives the selected cylinder index in the sample data - that's
what his Uemis does, and it makes sense for any dive computer that
supports multiple pressure transmitters.
However, the other case is a dive computer where the pressure samples
are all from cylinder 0, and any other cylinder will have the starting
and ending pressure set by hand. And the gas change events show when
the cylinder change happened.
So this creates a "turn gas change events into pressure sample fixups"
phase just before we actually analyze the pressures. That way the
pressure analysis can alway sdo the right thing, regardless of how the
data was originally stores in the dive.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the dive computers that give cylinder change events, we want to
re-write the cylinder index and pressure information with the event
information before we start analyzing the pressures. So instead of
filling the plot info and analyzing in one loop, split it up into two
phases. We'll do the "fix up cylinder pressure info based on events" in
between those phases.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The code keeps track of the segments of time when a specific tank was used
and interpolates the pressure values for that tank based on a simulated
average SAC rate for the times in which no pressure readings are
available.
This changes the way we used to plot the pressure when only beginning and
end pressure of a tank are known; it used to be a straight line, now it is
a sloped line where the steepness of the slope is proportional to the
depth at that point - which is much more realistic.
We also plot the pressures in two colors now. The old green for pressure
data that came from the input file (that is not the same thing as saying
it came from the computer - divelog for example appear to create pressure
readings in the samples even if it only has beginning and end pressure).
Interpolated values are plotted in yellow. If you have a sub-standard dive
computer which has a frequently failing pressure sensor, you can now tell
the parts of the plot where data was missing and we are filling in.
The function that prints the pressure text labels had to be completely
redone as it previously assumed one tank for the whole dive and
simplisticly printed that tank's start and end pressure at the beginning
and end of the profile plot with the y-values being the maximum and
minimum pressure...
This commit introduces a custom simplistic single linked list data
structure to keep track of the pressure information per segment - Linus
hated the idea of using GList for this purpose, and I have to admit that
in the end this was very straight forward to implement and made the code
easier to read and debug.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
This isn't right if you switch back to the same cylinder multiple times,
but for the first time it kind of works - just take the beginning
cylinder pressure if we have one.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Too much cut-and-paste, as Dirk points out. With multiple cylinders,
we're not necessarily going to start at time zero.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It doesn't actually do multiple cylinders correctly yet, but it should
be a nice framework for it. And accidentally (not) it also ends up
drawing the final line for the end pressure of a single-cylinder dive
that has been fixed up by hand too.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We draw a little red triangle (of hardcoded size - not sure if this SHOULD
scale with the size of the plot... I like it better if it doesn't) to the
left of an event.
We then maintain an array of rectangles that each circumscribe one of
those event triangles and if the mouse pointer enters one of these
rectangles then we display (after a short delay) a tooltip with the event
text.
Manually creating these rectangles, maintaining the coordinate offset,
checking if we are inside one of these rectangles and then showing a
tooltip... this all seems like there should be gtk functions to do this by
default... but if there are then I failed to find them. So instead I
manually implemented the necessary logic.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Previously we passed in width and height and the routine itself decided to
keep 5% margin around each edge - oddly doing this with double precision,
even though this is all integer coordinates.
Instead we are now passing in a drawing_area. We are kind of abusing the
cairo_rectangle_int_t data type here - but it seemed silly to redefine a
new data type for this.
Width and height give the size of the TOTAL drawing area (as before).
x and y give the offset from the edges - so the EFFECTIVE drawing area is
width-2x and height-2y
This is in preparation for adding tooltips - those need to know the
coordinate offsets from the edges - so having this hard coded inside the
plot function didn't make sense anymore.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
And don't artificially end dives on min pressure
This may be a problem for dive computers like Linus' Suunto Vyper Air
where the failure mode seems to be _high_ pressure readings (that's scary,
btw). If the transmitter fails at the end of the dive the pressure plot
ends with incorrect high pressure. But that's simply a bug with the dive
computer and not something that subsurface should hack around. Maybe we
should offer a way to edit the incorrect data points instead.
Always ending on the minimum pressure is definitely wrong as it causes
bogus plots when you do a valve shutdown during the dive (which means that
valid data gets plotted incorrectly).
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
We were missing the last sample (which is usually a fast ascent).
Also, reduced the velocity smoothing to 15 seconds as the 30 seconds were
hiding too much valid information
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
This is *really* ugly. We really should just create some kind of widget
that when moused over will show the event. Or something. Rather than
putting text on top of other text: the events - when they happen - are
usually bunched together (PO2 warnings, max depth, fast ascent leading
to mandatory safety stop, you name it).
But at least this way we see that the data is there, even if we see it
in ugly ways.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The plot_info was never freed, so every time you'd plot something, we'd
leak memory.
I'm running valgrind to see if there's anything bad going on. So far it
all looks fairly benign.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the actual degree sign for temperatures (°F and °C), and make sure
everything uses the proper "set_source_rgb[a]()" wrappers to set the
colors.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dirk wrote this before we have the 'plot_info' structure with the
cleaned-up dive info. No need to maintain that separate array of depths
and seconds.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following are UI toolkit specific:
gtk-gui.c - overall layout, main window of the UI
divelist.c - list of dives subsurface maintains
equipment.c - equipment / tank information for each dive
info.c - detailed dive info
print.c - printing
The rest is independent of the UI:
main.c i - program frame
dive.c i - creates and maintaines the internal dive list structure
libdivecomputer.c
uemis.c
parse-xml.c
save-xml.c - interface with dive computers and the XML files
profile.c - creates the data for the profile and draws it using cairo
This commit should contain NO functional changes, just moving code around
and a couple of minor abstractions.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
If the velocity is slower than FAST then we look back up to 30 seconds and
calculate the velocity for the past 30 seconds instead.
For the first version I'm not doing the average of the changes but simply
the change from beginning to end.
The alternative would be to do another triangle smoothing or something
like that - but as we don't know how many samples we have in the 30 second
window, it's a little harder here.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
This annoyed me from the first moment Linus added the tank pressure graph.
As the pressure goes down, the graph needs to go down. Seriously.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
