This is made just to make the tests appear in the same
order of the SettingsObjectWrapper order of initialization.
Since the SettingsObjectWrapper is huge, this helps
checking if everything is correct.
Signed-off-by: Tomaz Canabrava <tcanabrava@kde.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
1) Reorganise existing items in Graph tab so that all gass pressure
items are together and all profile-related items are together.
2) Provide units (mostly bar) for all settings having units.
Signed-off-by: Willem Ferguson <willemferguson@zoology.up.ac.za>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Changes to the heatmap image in the user manual as well as some small changes
to sync the text with the new image.
Signed-off-by: Willem Ferguson <willemferguson@zoology.up.ac.za>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
1) Replace the existing graphics for explaining the heat map.
2) Update the text for explaining the heat map.
These changes with substantial input from Rick Walsh.
Signed-off-by: Willem Ferguson <willemferguson@zoology.up.ac.za>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Calculate gfline using the gradient factor that is set by the planner
preferences when in the planner, and by the general prefs when not in the
planner. This is achieved by doing the gradient factor calculation in dive.c,
where buehlmann_config is defined.
Previously, the gfline was calculated using the general preferences gfhigh and
gflow, even when in the planner.
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Call the emitDataChanged slot when ascent and descent rate spinboxes lose
focus. Without this connection, rates are not updated immediately after
editing the value with keyboard numbers and hitting tab or enter.
It is necessary to keep the valueChanged(int) connections, because
editingFinished() is not triggered by changing the value with the arrows.
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Call GasSelectionModel::instance()->repopulate() when creating the initial
simple dive. Without this call, the gas selection dropdown list does not work
in the DivePLannerPointsModel table until the cylinders table has been edited.
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
This is a bit ugly since it does a regexp match on
divesite.notes but what can I do...
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Stretch out the yellow zone of the HSV scale, because the yellow band of the
true scale appears narrow.
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Color "undersaturated" values relative to inert gas pressure of gas being
breathed, rather than relative to inert gas pressure of air.
Also change slightly the point at which bright green (hue = 120 deg) from 10%
of M value to 0% of M value (=ambient pressure).
Other than the slight shift in lower bound of the green-red scale, this does
not affect the colors of the tissues with inert gas pressure greater than
ambient pressure, which are relative to the Buhlmann M value.
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
By drawing oversize dots for each data point, dots were overlapping such that
the change in tissue presssure wasn't displayed at the right time - typically
out by 1-2 minutes, depending on dive duration.
Drawing a line between discrete points, the data points don't overlap and
change in tissue pressure is displayed at the right time.
Signed-off-by: Rick Walsh <rickmwalsh@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Fixes a couple of issues with the tests.
Also, a type in prefs.h is "short" while it's actually
a boolean, this made me write the wrong testcase for this.
Fixed this by setting the Qt wrapper to bool, but I didn't
changed the c implementation because I tought I could break
something.
Signed-off-by: Tomaz Canabrava <tcanabrava@kde.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Biggest test that I created. test all of TecDetails
information. Untested.
Signed-off-by: Tomaz Canabrava <tcanabrava@kde.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
This does the basic export as a TeX file including a template.
It still lacks proper location parsing.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
When merging dives, this will skip the gas change event if both dives
use same gas.
Fixes#1099
Signed-off-by: Miika Turkia <miika.turkia@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
... as those are needed for the heatmap and not only
for Buehlmann ceilings.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
We need to read the file given as parameter, not the first in list.
Signed-off-by: Miika Turkia <miika.turkia@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
...otherwise we show garbage before the mouse enters the
profile for the first time.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
