Most divecomputers download data dive by dive - so we get reasonably
frequent updates during the download (as new dives are found and posted
in the progress text area). But some (like the G2) download all of the
new dives at once and only then start parsing them. As a result the
download can look like it is hung.
As a compromise this shows updates on the data received in 10kB
increments. Which for most cases should never be shown and therefore not
make the user experience any worse - but for cases like the G2 will make
a huge difference.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Qt 6 will drop support for QRegExp.
Use QRegularExpression instead.
Much of this is a simple replacement of one class with the other, but
there are some changes to the way matches are tracked and captures are
created. Also, the exactMatch now needs to be implemented via anchors in
the regular expression itself.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Qt 6 will drop support for QRegExp.
Use QRegularExpression instead.
This is a straight forward replacement without any other code changes.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Fix a pair of warnings, which annoyed me for a long time:
For some reasons prefs.bottompo2 is an integer (mbar)
whereas prefs.modpO2 is a float (bar). This results
in mixed integer/floating point arithmetics when
conditionally using either of them. And ultimately
a warning, when storing a mbar value as an integer.
Fix this by an explicit cast to int after converting
modpO2 to mbar.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Air is a special gas that does not contain oxygen according
to gasmix.o2.fraction. If you want to use the fo2, you
need to use get_o2() to treat this special case correctly.
This fixes a bug when setting the MND of a gas containing
21% oxygen when o2 is considered not narcotic.
Reported-by: Christoph Gruen <gruen.christoph@gmail.com>
Signed-off-by: Robert C. Helling <helling@atdotde.de>
When we found an invalid sensor (referring to a non
existing cylinder) in fixup_dive() the sensor-id was
set to NO_SENSOR.
This led to invalid XML files, because the code decides
to switch into legacy mode. However, there are two
pressure readings, which is invalid in legacy mode.
Therefore, also clear the pressure data.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
This tries to make our fingerprinting code work better, by avoiding
using the "deviceid" field that has always been unreliable because we've
calculated it multiple different ways, and even for the same version of
subsurface, it ends up changing in the middle (ie we calculate one value
initially, then re-calculate it when we have a proper serial number
string).
So instead, the fingerprinting code will look up and save the
fingerprint file using purely "stable" information that is available
early during the download:
- the device model name (which is a string with vendor and product name
separated by a space)
- the DC_EVENT_DEVINFO 32-bit 'serial' number (which is not necessarily
a real serial number at all, but hopefully at least a unique number
for the particular product)
but because the model name is not necessarily a good filename (think
slashes and other possibly invalid characters), we hash that model name
and use the resulting hex number in the fingerprint file name.
This way the fingerprint file is unambiguous at load and save time, and
depends purely on libdivecomputer data.
But because we also need to verify that we have the actual _dive_
associated with that fingerprint, we also need to save the final
deviceid and diveid when saving the fingerprint file, so that when we
load it again we can look up the dive and verify that we have it before
we use the fingerprint data.
To do that, the fingerprint file itself contains not just the
fingerprint data from libdivecomputer, but the last 8 bytes of the file
are the (subsurface) deviceid and the diveid of the dive that is
associated with the fingerprint.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only used in context of acquiring GPS locations with the mobile app, which
we no longer do.
Keep the DiveAndLocation structure around as that's needed by the
ApplyGpsFixes command.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
In commit 4724c88 get_plot_details_new was updated to pass an index
instead of the entry into plot_string. This means we are passing "i" to
plot_string after the final increment of the for loop, instead of
getting the entry[i] within the loop before the final increment. This
means if we are mousing over the far right of the graph, where the time
based break is not hit, we will end up passing an index equal to nr-2
instead of nr-3, which is intended to shave off the final two rows
containing data not useful to the display.
There are a handful of ways to fix this. This commit intends to be
consistent with stylistic choices made elsewhere in the project.
Signed-off-by: Josh Torres <torres.josh.j@gmail.com>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
We want to prevent the user from accidentally deleting a
cylinder with sensor readings. Therefore, we need such a
function.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Due to changes in the handling of sensor-ids, invalid XMLs were
generated. In particular, these contained duplicate attributes
in the sample tags.
Even though these files shouldn't exist, let's try to parse
them anyway. Some data will be lost, but that's better than
not opening the file.
libxml2 can be told to try to recover from such petty(?) errors
by passing the XML_PARSE_RECOVER flag.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
For dives with mixed divemode, one needs to check sample.setpoint
to figure out if the segment is an OC segment and the po2 needs
to be computed from the gasmix and ambient pressure.
This fixes#3310
Signed-off-by: Robert C. Helling <helling@atdotde.de>
We no longer need the remove infrastructure, and the edit nickname function
becomes much more intuitive to use by passing in the dive computer for
which we want to create a nickname instead of the internal index into
the array of devices.
This also removes / simplifies the device list update signals in the
DiveListNotifier.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
This makes it much easier to manipulate dc nickname entries. In order
for that to work we can't simply remove entries with empty nickname (but
that isn't needed, anyway, as the code that saves XML or git already
handles that case correctly).
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
... it just causes problems later when we free them, since we don't do
any reference counting.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we save the divecomputer data, we never actually save the serial
value as a field. We used to rely on saving the very dodgy 'deviceid',
and then look up the serial number from there. And that never really
worked reliably, but we didn't really notice, because we never really
_used_ the serial number anywhere.
The only place the serial number is actually reliably displayed is in
the "Extra data" tab, which contains the key value pairs, and that's
where the original dive download code got the serial number from.
So just parse that at load time too, the same way we parsed it at dive
download time.
In fact, do the firmware version the same way, and remove the code from
the downloader, since it too can rely on 'add_extra_data()' just picking
up the information directly.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have this odd legacy notion of a divecomputer 'device', that was
originally just basically the libdivecomputer 'EVENT_DEVINFO' report
that was associated with each dive. So it had firmware version,
deviceid, and serial number.
It had also gotten extended to do 'nickname' handling, and it was all
confusing, ugly and bad. It was particularly bad because it wasn't
actually a 'per device' thing at all: due to the firmware field, a dive
computer that got a firmware update forced a new 'device'.
To make matters worse, the 'deviceid' was also almost random, because
we've calculated it a couple of different ways, and libdivecomputer
itself has changed how the legacy 32-bit 'serial number' is expressed.
Finally, because of all these issues, we didn't even try to make the
thing unique, so it really ended up being a random snapshot of the state
of the dive computer at the time of a dive, and sometimes we'd pick one,
and sometimes another, since they weren't really well-defined.
So get rid of all this confusion.
The new rules:
- the actual random dive computer state at the time of a dive is kept
in the dive data. So if you want to know the firmware version, it
should be in the 'extra data'
- the only serial number that matters is the string one in the extra
data, because that's the one that actually matches what the dive
computer reports, and isn't some random 32-bit integer with ambiguous
formatting.
- the 'device id' - the thing we match with (together with the model
name, eg "Suunto EON Steel") is purely a hash of the real serial
number.
The device ID that libdivecomputer reports in EVENT_DEVINFO is
ignored, as is the device ID we've saved in the XML or git files. If
we have a serial number, the device ID will be uniquely associated
with that serial number, and if we don't have one, the device ID will
be zero (for 'match anything').
So now 'deviceid' is literally just a shorthand for the serial number
string, and the two are joined at the hip.
- the 'device' managament is _only_ used to track devices that have
serial numbers _and_ nicknames. So no more different device
structures just because one had a nickname and the other didn't etc.
Without a serial number, the device is 'anonymous' and fundamentally
cannot be distinguished from other devices of the same model, so a
nickname is meaningless. And without a nickname, there is no point in
creating a device data structure, since all the data is in the dive
itself and the device structure wouldn't add any value..
These rules mean that we no longer have ambiguous 'device' structures,
and we can never have duplicates that can confuse us.
This does mean that you can't give a nickname to a device that cannot be
uniquely identified with a serial number, but those are happily fairly
rare (and mostly older ones). Dirk said he'd look at what it takes to
give more dive computers proper serial numbers, and I already did it for
the Garmin Descent family yesterday.
(Honesty in advertizing: right now you can't add a nickname to a dive
computer that doesn't already have one, because such a dive computer
will not have a device structure. But that's a UI issue, and I'll sort
that out separately)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If we download a first dive computer and add a dive site to the dive (by
setting a location name for example), and then download from another
dive computer that provides us with GPS data, we should keep the
existing dive site information, but add the GPS data from the freshly
downloaded dive computer.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
This adds a cleanup function to be called after a divelogs.de upload
finishes (successful or not) to make sure the temporary zip file is
closed and removed.
Signed-off-by: Richard Fuchs <dfx@dfx.at>
On multi-user systems with a shared directory for temporary files, using
a static file name can lead to permissions problems and subsequent
errors due to collisions. Use a random unique file name for each
generated file to avoid these problems.
Note: the temporary file generated from the divelogs.de upload is still
left behind after the upload finishes.
Signed-off-by: Richard Fuchs <dfx@dfx.at>
The intent of the code was to check that there is a string and it has at least
two characters. Since iter is the result of a strchr(iter, '|') call, we
know that if iter isn't NULL, iter[0] is '|', so we only need to check the next
character.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
try_to_xslt_open_csv() re-allocates the memory passed in (not really great as
far as design goes, maybe something that should be reimplemented). Doing
pointer arithmatic with the returned base pointer results in garbage, unless
one gets super lucky and the realloc manages to not move the memory.
It's a wonder this ever worked.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Before making the cylinder-table dynamic, dives always
had at least one cylinger. When such a dive is displayed,
the TabDiveInformation class calls per_cylinder_mean_depth().
If there are no samples, this function generates a "fake
profile" with fake_dc(). Thus, effectively dives always
had samples once the user was displaying them.
When the cylinder-table was made dynamic, dives without
cylinders were supported. This can notably happen, when
importing from CSV (this could actually be a bug).
per_cylinder_mean_depth() exits early in that case and
doesn't create a fake profile. This lead to crashes
of the profile-widget, which were fixed in 6b2e56e513.
Non-sample dives were now shown with the Subsurface-logo.
To restore the previous behavior, genarate a fake profile
for sample-less dives in fixup_dive(), which is called
anytime a dive is loaded or imported. This seems to
have been the intention anyway and this worked only
"by chance". This will make a few fake_dc() calls obsolete,
but so be it.
Since fake profiles are now generated on loading,
the parse-tests need to be fixed to account for that.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
When merging two dives, the higher CNS value was taken. This could
result in inconsistent CNS values if two dives were merged where
one dive's CNS was calculated from a "fake profile", i.e. a dive
without dive-computer profile. In that case, the most conservative
value (all time spent at the bottom) was assumed. The merged dive
then consisted of the dive-computer profile and the conservative
CNS estimate.
This is fixed by setting the CNS value to "0" after merging,
which means "unknown". The correct value will then be recalculated
in "fixup_dive" from the actual sample data.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The data of the membuffer is passed as a data/length pair
to xmlReadMemory(). There is no point in NUL-terminating it.
Moreover, pass the data directly to xmlReadMemory()
instead of via variables. These variables are reused
later with a different meaning, making this super-confusing.
The membuf variable is turned from "const char *" to "char *"
to signal that we own the buffer.
Amazingly, zip_source_buffer() frees the buffer, even though
a "const void *" is passed in. This API is pure madness. Add
a comment.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Thus, the membuffer data is automatically freed when going
out of scope - one thing less to worry about.
This fixes one use-after-free bug in uploadDiveLogsDE.cpp
and one extremely questionable practice in divetooltipitem.cpp:
The membuffer was a shared instance across all instances
of the DiveToolTipItem.
Remves unnecessary #include directives in files that didn't
even use membuffer.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
C-style memory management is a pain and nearly nobody seems to get
it right. Add a C++-version of membuffer that frees the buffer
when it gets out-of-scope. Originally, I was thinking about
conditionally adding a constructor/destructor pair when compiling
with C++. But then decided to create a derived class membufferpp,
because it would be extremely confusing to have behavioral change
when changing a source from from C to C++ or vice-versa.
Also add a comment about the dangers of returned pointer: They
become dangling on changes to the membuffer.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The sensor-id in the sample struct was a uint8_t, with all
the known problems of unsigned integers. In the rest of the
code cylinder ids are signed integers. To avoid confusion,
make it a signed int. int8_t should be enough (max. 127
cylinders). To allow for degenerate cases, use an int16_t.
16k cylinders should be enough for everyone.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The code will happily perform out-of-bound accesses if
pressure-sensors refer to non-existing cylinders. Therefore,
sanitize these values in fixup_dive(), which is called
everytime a dive is loaded or imported.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
By default, the parser would create samples with cylinder
ids 0 and 1. This creates out-of-bound accesses for the
common one-cylinder (or even no-cylinder) dives. These
were harmless when the cylinder-table was of a fixed size.
Since changing to a dynamic cylinder-table, these became
actual out-of-bound accesses. Don't create such samples
in the parser.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The sensor member of sample refers to a cylinder from which
the pressure was read. However, some dives don't even have
a cylinder. Therefore, introduce a special NO_SENSOR value
for these dives. Since the cylinder is given as a uint8_t,
0xff seems to be a sensible choice.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
When user has selected to show unused cylinders in equipment tab,
respect this setting when exporting to divelogs.de.
Fixes#3277
Signed-off-by: Miika Turkia <miika.turkia@gmail.com>
This is adding the capability to select 'Dive number' and 'Date / Time'
in the 'Copy dive components' dialog, and then copy them into the
clipboard.
When using 'Paste dive components, these values will then be pasted into
the selected dive(s).
This is intended to help with workflows that import dive information
from two different sources, like general information from another
logging program, and CCR ppO2 sensor readings from a unit log, and then
stitch them together into one cohesive entry with all data per dive.
Copied data is also output into formatted text when pasting the
clipboard outside of the application:
```
Dive number: 401
Date / time: Sun 2 May 2021 12:00 AM
```
No translations have been added as of now - I could not find any
information on how strings are translated for this project.
Signed-off-by: Michael Keller <github@ike.ch>
The color was misnamed, since it has only been used for the
duration line for quite some time (since 893bea700c to be
exact).
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
the last manually entered waypoint but consider the
possibility that it should first top where we are
before the next stop depth has cleared.
Reported-by: David Carron
Signed-off-by: Robert C. Helling <helling@atdotde.de>
It looks like libxml2 has some internal limitations by default that
causes parse failures in some situations. Avoid them with
XML_PARSE_HUGE.
Without this, you get errors like
test.xml:349250: parser error : internal error: Huge input lookup
όμουν τουλάχιστον αλλά +2kg και ενδεχομένως +4
^
when something in the xml file grows too large.
I don't know libxml2 internals, so I have no idea what exactly goes
wrong, but the docs say:
XML_PARSE_HUGE = 524288 : relax any hardcoded limit from the parser
and that makes us successfully parse the Greek file from Kostas.
Reported-by: Kostas Katsioulis <kostaskatsioulis@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the ARRAY_SIZE macro into a header file and use it to determine the
number of cloud servers that we need to check.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
If we can't reach the cloud server in the URL (which might come from the
settings or be passed in by the user), we try the alternative server(s).
If we end up changing servers, we need to update the remote that we have
already parsed from the URL.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
If we can't reach our preferred server, try using a different one.
The diff makes more sense when ignoring white space.
With this we check the connection to the cloud server much earlier and
in case of failure to connect try a different cloud_base_url.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
With the new names for the cloud server we'd get different local cache
directory names depending on which server gets used. In order to avoid
that, normalize the name before generating the hash that determines the
local directory name.
Additionally, the old code had an extra '/' in the URL, due to the way
the URL was assembled. Again, to match the existing hash for people
upgrading from older Subsurface versions, add that to our normalized
name as well.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
The backend infrastructure will soon be able to support more than one
cloud server which automagically stay in sync with each other.
One critical requirement for that to work is that once a session was
started with one of the servers, the complete session happens with that
server - we must not switch from server to server while doing a git
transaction. To make sure that's the case, we aren't trying to use DNS
tricks to make this load balancing scheme work, but instead try to
determine at program start which server is the best one to use.
Right now this is super simplistic. Two servers, one in the US, one in
Europe. By default we use the European server (most of our users appear
to be in Europe), but if we can figure out that the client is actually
in the Americas, use the US server. We might improve that heuristic over
time, but as a first attempt it seems not entirely bogus.
The way this is implemented is a simple combination of two free
webservices that together appear to give us a very reliable estimate
which continent the user is located on.
api.ipify.org gives us our external IP address
ip-api.com gives us the continent that IP address is on
If any of this fails or takes too long to respond, we simply ignore it
since either server will work. One oddity is that if we decide to change
servers we only change the settings that are stored on disk, not the
runtime preferences. This goes back to the comment above that we have to
avoid changing servers in mid sync.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
We know the preference is never empty, so stop testing for this. But
don't maintain two different preferences with basically the same
content. Instead add the '/git' suffix where needed and keep this all in
one place.
Simplify the extraction of the branch name from the cloud URL.
Also a typo fix and a new comment.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
This was a hack for a very early SSL certificate that was rejected on
some platforms. We haven't used that one in ages, so let's just remove
the whole hack - but always show in the console output when there was an
SSL error.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
The dive selection was initialized during data-reset. However,
this emitted a signal before all data-reset routines were run.
Ultimately, this led to access-after-free in the statistics code.
Instead, move the select_newest_visible_dive() signal from the
divelist-model to the process_loaded_dives() function. There
is no point in initializing the selection if the dive data
is cleared after all.
This change broke closing of the log, because the UI-selection
was not reset. Therefore, when clearing the data, clear the
selection before proceeding with clearing.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
In 9bfc6d252, testing of the planner was changed to use the
planner_ds parameter instead of a global variable.
Unfortunately, two conditionals were inverted, leading to
an erroneous ceiling calculation when in the planner.
Restore the proper conditions. Moreover, instead of testing
the planner_ds parameter, use the already existing in_planner
flag, which is derived from said parameter.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Both the calculations for CNS and OTU did not take
into account the pO2 drop when using a PSCR. Furthermore,
there was some unit confusion due to not using internal
units.
Reported-by: arosl
Signed-off-by: Robert C. Helling <helling@atdotde.de>
When parsing "event 123" (?) a picture is added, without
initializing the picture structure. Thus, a picture with a
random gps location is added.
Use the "empty_picture" initializer to avoid that. Fixes a
Coverity warning.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
We used to round the ceilings for the individual tissues with
%.1f but the maximal (and thus effective) ceiling only with
%.0f. This makes no sense or be rounded up (to the conservative
side).
This commit shows also the maximal ceiling with higher accuracy.
Reported-by: Peter Hübner
Signed-off-by: Robert C. Helling <helling@atdotde.de>
When doing OC bailout from a CCR dive, there could still
be pO2 sensor readings but those are not valid.
This fixes a problem noticed by Justin Ashworth.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
Even when diving a CCR, the pO2 cannot exceed ambient
pressure. This only makes a difference at shallow depths.
Fix this in the calculation of OTUs and CNS.
This affects some tests that now have slightly different CNS and OTU values.
Suggested-by: Justin Ashworth
Signed-off-by: Robert C. Helling <helling@atdotde.de>
We had a user request to allow for setpoint changes
at certain depths for CCR deco.
You can now enter a cylinder with name like
"SP 1.4" ('S' and 'P' and ' ' and a float) with
a switch depth and that cylinder is interpreted as
a depth dependent setpoint switch.
This user interface is a hack. But I believe that such
setpoint changes are similar enough to gas switches during
deco and should thus be handled in a simiar manner.
I would be happy to hear ideas how this could be made
less easter eggish.
Suggested-by: Justin Ashworth
Signed-off-by: Robert C. Helling <helling@atdotde.de>
The application state is a desktop-only thing. The mobile UI
also has its application state, but that is something completely
different.
The last remaining user of the application state was to flag
whether the planner is active. Since this has all been
unglobalized, the ApplicationState structure can be moved
from core to the desktop UI. And there it can be made local
to the MainWindow class.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The TemplateLayout prints different dives depending on
whether the planner is active. Instead of accessing a
global variable, pass the status down from the MainWindow.
That's all quite convoluted, since there are multiple
layers involved.
On the positive side, the in_planner() function has now
no users an can be removed.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
To remove reliance on global state, pass an "in_planner" argument
to decoMode(). Thus, calls to in_planner() can be removed.
This is a more-or-less automated change. Ultimately it would
probably be better to pass the current deco-mode to the affected
functions instead of calling decoMode() with an in_planner
parameter.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
To remove reliance on global state, pass an "in_planner" argument
to clear_deco(). Thus, calls to in_planner() can be removed.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
To remove reliance on global state, pass an "in_planner" argument
to vpmb_next_gradient(). Thus, calls to in_planner() can be removed.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
To remove reliance on global state, pass an "in_planner" argument
to add_segment(). Thus, calls to in_planner() can be removed.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The icons shown in the dive list were rendered for every single
access. Render them only once. This supposes that the
defaultIconMetrics structure does not change once the icons are
rendered!
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
There was the "application state", which decided what to show
in the "quadrants" and the "view state" which decided which
quadrant to show. These interacted in a hard-to-grasp way.
The "view state" is used to show the map or dive list in
full screen.
I simply couldn't get these two orthogonal states to interact
properly. Moreover the thing was buggy: If a quadrant was hidden,
the user could still show it, by dragging from the side of the
window, at least under KDE.
To solve these woes, merge the two states into a single
application state. If the widget of a quadrant is set to null,
don't show it. So the four "view states" are now "application
states" where three of the four quadrants are not shown.
This also changes the memory management of the widgets:
widgets that are not shown are now removed from the QSplitter
objects. This makes it possible that the same widget is
shown in *different* quadrants.
While writing this, I stumbled upon a Qt bug, which is known
since 2014:
https://forum.qt.io/topic/43176/qsplitter-sizes-return-0
When restoring the quadrant sizes there was a test whether
the quadrant size is 0. If that was the case, a default size
was set. This seems not to work if the widgets were recently
added. Since this test now always fails, make the quadrants
non-collapsible and thus guarantee that 0 is never saved as
a size.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Somehow three identical lines snuck into commit 0a4e37ee8b ("core/BT: simplify
detection of bluetooth names").
Reported-by: Henrik Brautaset Aronsen <subsurface@henrik.synth.no>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Instead of that super long if-else if chain, have something more
structured using a table for the common case of prefix based names.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
It would be so much nicer if we could just let libdivecomputer do this,
but the filter function there doesn't quite do things the way we need
them to be. Which is why we have our own function here.
This is a small attempt to rationalize the code that we have to make it
easier to maintain.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
The goal is to enable a user experiencing crashes when applying GPS data
to their dive log to make all necessary data available to the
developers. Hopefully the clipboard is large enough to hold all the
data.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
This only read accesses the dive and constructs a plot-info
structure. Make the dive parameter const.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
This function initializes decompression data from a dive.
The dive is not modified, therefore make it const.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
We need to do this before the preferences are loaded, or the system
default size is lost. Given that our other sizes are all relative to
this value, that would be a problem.
With this we can now ensure that we always have the right font size for
smaller, regular, and larger theme settings.
Also removes some obsolete commented out code.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Adds fields to the advanced preferences page to modify GFLow and GFHigh for
the Buhlmann decompression model for calculating ceilings. Updated preferences
code to set the Buhlmann parameters in core/deco.c when the GF prefs are
updated.
Signed-off-by: Doug Junkins <douglas.junkins@gmail.com>
First, the time zone adjustment was wrong - this as written could only
ever have worked in UTC or by pure chance.
Second, the order of alerting the UI of the availability of a GPS fix
was also incorrect creating a race between the UI and our data
structures.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
When setting a CCR setpoint, the profile code(!) would turn
the dive into a CCR dive. Not only should the display layer
not alter dives, this also means that the action is not
undoable.
Move that to the appropriate undo command, where it makes
more sense, but obviously also makes things more complicated.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The make_first_dc() function clones a dive with a certain dive
computer moved to the front. This is used by the
MoveDiveComputerToFront undo command.
make_first_dc() calls invalidate_dive(). However, the undo
command does that by itself on every undo/redo. Thus,
remove the call in make_first_dc().
Aside from consistency, the goal is to move invalidate_dive()
to command/* so that we can be more aggressive about the whole
topic: Store only "const dive *" pointers and thus force any
writing access to explicitly invalidate the dive cache.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The DiveHandler shows a context menu where a cylinder can be
chosen. This indirectly accesses the global displayed_dive
variable.
Remove this in a step to make the profile reentrant.
The code was quite ominous: instead of simply generating the
list of cylinders, a global model was reset and then accessed
with Qt's cumbersome model/view API. All this trampling over
global state can be removed by simply making the function
that generates the list globally accessible.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Instead of accessing the global displayed_dive variable
in RulerItem, pass the dive. This is a step in making the
profile reentrant.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Instead of accessing the global displayed_dive variable,
pass the dive to the various profile items. This is a
step in making the profile code reentrant.
This removes the last user of the displayed_dc macro,
which can now be removed.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Don't access the global displayed_dive variable in an effort
to make the profile reentrant.
Note that this still accesses the global dc_number variable,
which will likely have to be removed.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The profile item that shows the ceilings adds a warning event
if the ceiling is violated. This is very unfortunate.
Improve this situation by adding the event up to the function
that calculates the ceiling. This is still not how it should
be - the display layer should not modify the dive that it
displays.
To make this clear, add a comment that details that this
is a contract between planner and display layer: The planner
uses a dive that can be trampled upon by the profile.
Still, this should be solved differently.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The in_planner() function is incompatible with a reentrant
profile, since it accesses a global variable. In
create_plot_info_new() it is essentially redundant, because
there is a planner_ds (ds = deco_state) parameter that
is used only when in the planner. Therefore use that as
the in_planner indicator: when non-null, the profile is
showing a planned dive.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
New (late 2020) iX3M hardware (refered to as 'iX3m with Sequared Buttons'
in the Ratio support section) appears to identify as iX5M, both in the
Bluetooth name and reported revision e.g.
$ ./ratio-toolbox-x86_64.AppImage info | head -n2
Model: Ratio® iX5M GPS TECH+
Firmware version: 4.1.26/016 (English)
Add a second Bluetooth name matcher for this variation, returning the same
(generic) model as is currently used.
Signed-off-by: Damian Zaremba <damian@damianzaremba.co.uk>
Add a new "statistics" application state. In the statistics state
show the statistics widget and the filter in the top quadrants.
The idea is to allow filtering and doing statistics at the same
time.
Sadly, we can't use the filter-widget in different quadrants,
because Qt's ownership model is completely broken / inflexible.
It does not support a widget having different parents and
thus a widget can only belong to one QStackedWidget.
Hiding the map in the statistics view is quite hacky:
Since the view of the quadrants is not determined by the
"ApplicationState", we have to restore the original quadrant
visibility when exiting the stats mode. Therefore, set the
original visibility-state when changing application state.
The MainWindow-quadrant code really needs to be rewritten!
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Simply move the initialization of the logging function into its own method and
call that in the QMLManager constructor.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
These were declared in pref.h and defined in subsurfacestartup.c.
pref.c didn't even exist. Create it and move preferences-related
structs and functions there.
setup_system_prefs() is left in subsurfacestartup.c, since it
works with environment variables.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The function is declared in core/unit.h, therefore it seems logical
to define it in the corresponding source file.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The user preferences can never end up with PASCAL pressure
units. The only place that uses these units is the XML parser.
Therefore, remove the PASCAL case in get_pressure_units().
This will remove an unused translation string.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The way I understand, the PASCAL pressure unit is used to parse
obscure dive logs. However, there is no support in the UI for
using Pa as pressure unit. Therefore remove reading / writing
this unit to git divelogs.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The get_*_unit() functions return the unit-name as set in
the preferences. Add versions with a "metric" parameter.
This will be used by the statistics code, which may in
the future allow for binning with alternative units.
All the unit-formatting functions should probably be moved
away from qthelper to their own source file.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
This was only used by the filter, but will also be used
by the statistics module. To avoid duplicate translation
strings, move to a common place.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The start-selection widget will need icons with a transparent
background so that the icons don't stick out like a sore thumb.
So far the icons rendered by this function were only used by
the images on the profile and were perfectly rectangular.
Therefore there was no need for this.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Create a gastype enum, which describes the type of a gas.
For now: air, nitrox, normoxic, trimix and oxygen.
This probably should be made configurable.
The gas types will be used to bin gasses in the statistics
module.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The renderIcon() function was used by the thumbnailer to
render SVG-based icons. Move it to the global qthelper.cpp
so that it can also be used by the statistics module.
Add "SVG" to the name to emphasize what it is used for.
For consistency also move the renderSVGIconWidth() function,
which renders to a fixed width, to qthelper.cpp
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Weirdly, this function was declared in dive.h and defined in
subsurface-startup.c. Let's move declaration and definition to
more appropriate places, viz. subsurface-time.h and time.c.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
This function was not used anywhere. Moreover, remove a few
unused includes from qthelper.h. Surprisingly, a number of users
of qthelper.h depend on these, so readd them at the appropriate
places.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Arguably, the number of filtered dives is a matter of the divefilter.
Let's move it there.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
When removing dives, the UndoCommands would keep track of the
shown dives. When adding, they were calling into the filter
instead. Let's remove this asymmetry.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The shown_dives variable was reset by the dive_list code. Arguably,
the filter should keep track of the number of shown dives, so move
the resetting there. This means adding a new "reset()" member function
to the filter and call that instead of "updateAll()" when the core
data is reset.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Since switching to the mobile-models and removing grantlee,
DiveObjectHelper was demoted to a thin wrapper around string
formatting functions. The last user was removed in a previous
commit.
It was never a good idea, given QML's strange memory-management.
Let's remove it.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
When editing a dive, a DiveObjectHelper of the unmodified dive
was created to compare the edited with the old values. Since
the DiveObjectHelper is used here only as a pointless wrapper
around the formatting functions, call these functions directly.
However, note that the code is in principle wrong since the
change to the mobile-models, which do not use the DiveObjectHelper.
The real fix would be to reload the data from the model to prevent
going out-of-sync with respect to the formatting routines!
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
With the removal of grantlee, this became pointless glue
code. Call the formatting functions directly.
Since the printing code was the only user of CylinderObjectHelper,
remove the whole thing.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
At this point (post grantlee), DiveObjectHelper is just pointless
glue code. Let's remove it from the printing code and call the
formatting functions directly. If necessary, move these functions
to core/string-format.cpp.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
This was a weird helper object, needed for grantlee. Instead
of storing this object, loop over cylinders and dives directly.
The actual accessor function is unchanged and now generates
a DiveObjectHelper or DiveCylinderHelper for every variable
access. Obviously, this is very inefficient. However, this
will be replaced in future commits by direct calls to formatting
functions.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The mobile version of the list used string formatting functions
defined in DiveObjectHelper and declared in mobilelistmodels.h.
Very confusing. Move them to a separate source file where - in
the long run - all the string-formatting functions, which
are scattered all over the place, can be collected.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Recently (d16a9f118a) the tankinfo table was made dynamic, which
means that the default tankinfos are added programatically.
Thereby, the wrong function was used for AL* type of cylinders:
metric instead of imperial. Fix those.
Reported-by: Michael Andreen <harv@ruin.nu>
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
A user complained about the default cylinders list. Provide
a preferences option to turn this off.
When changing the preferences, the tank-info model will be
completely rebuilt. Currently, this is a bit crude as this
will be done for any preferences change.
Suggested-by: Adolph Weidanz <weidanz.adolph@gmail.com>
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
There was a tank info with an empty name. According to a comment,
this is needed for the "no cylinder" case. However, we now support
empty cylinder tables, so this is not needed anymore. Therefore,
remove it.
Make sure that the user can still enter the empty name, just in
case. But don't save the size and pressure in that case.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
This is obviously a pure code-hygiene thing. But with the new
dynamic tank info table, this becomes trivial, so let's do it.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
The list of known tank types were kept in a fixed size table.
Instead, use a dynamic table with our horrendous table macros.
This is more flexible and sensible.
While doing this, clean up the TankInfoModel, which was leaking
memory.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
So far, the PreferencesDialog emitted a settingsChanged signal.
This meant that models that listened to that signal had to
conditionally compile out the code for mobile or the connection
had to be made in MainWindow.
Instead, introduce a global signal that does this and move
the connects to the listeners to remove inter-dependencies.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Provide supported dive computer list on the command line
and actually call the cli download. Still not functional.
Signed-off-by: Robert C. Helling <helling@atdotde.de>
This is of course not functional at all, but it gives a first idea of
what we will need to do in this code.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Right now this doesn't do a thing, but it gives us a nice target that
has far fewer dependencies and should contain enough parts to download
stuff from a divecomputer and then sync that with cloud storage.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
in_planner() is problematic, since it is uses desktop-only
application state. Since the cylinder-model already has
an appropriate inPlanner flag, use this instead.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
As we switched to the qmake based build we now bundle the translations
via the Qt resource system instead of explicitly as Android assets. This
adjusts the code that opens the translations accordingly.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
We don't support adding pictures and videos on mobile, so let's not
referernce the infrastrutcture that's needed for that.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
These are static functions, they cannot be used as a method on an object to
construct that object.
commit aa5f2e7c73 ("cleanup: replace deprecated sprintf()/vsprintf() calls")
introduced this bug in an ill-advised attempt to deal with a deprecation
warning.
This caused us to not print GPS coordinates in the UI.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Add a general dives-imported signal for those cases where we
want to fully rebuild models, notably, the completion models.
The divesAdded signals are too fine, because they are sent
per trip and we don't want to reload these models multiple
times per import.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
When breathing pure oxygen and considering it not
narcotic, there is not maximal narcotic depth and
the formula divides by zero. So better, handle this
case separately.
Fixes#3080
Signed-off-by: Robert C. Helling <helling@atdotde.de>
The scope confusion between s (the for loop variable) and s (the function
argument) caused a crash in the s.split() on Windows.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Recently the QStrings were replaced by std::strings in device.cpp
so that they can be accessed from C-code. However, libstd being
modelled after C, constructing a std::string from a NULL pointer
leads to a crash.
Fix one case where this was overlooked.
Moreover, replace a null-pointer check by empty_string(), to
treat NULL and "" equally.
Reported-by: Salvador Cuñat <salvador.cunat@gmail.com>
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
Because of subsequent changes there is no clean way to just revert the changes
introduced in commit 8b36cf1051 ("desktop: offer different colors for info tab
titles"), so this manually removes the parts we don't need anymore.
This also restores a tooltip value that was inadvertantly removed in that
commit.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Add a preference option to set the color of the text on the information tab to
either MediumBlue, LightBlue or Black. The last two of these colors are meant
to enable areadable font contrast on displays with dark mode.
The choice is saved with the other preferences.
[Dirk Hohndel: this isn't really about dark mode, so changed many of the types
and variable names, changed the user visible texts, and
addressed some whitespace issues]
Signed-off-by: willemferguson <willemferguson@zoology.up.ac.za>
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
When encountering a <weight> tag, we would parse into the last
weightsystem. However, we only create weightsystems when
encountering <weightsystem> tag. Therefore, this code would
either crash or overwrite the previous weightsystem.
Instead, create a new weightsystem for each <weight> tag.
Moreover, make sure that inside a <weightsystem> tag a
weightsystem actually exists. This should be the case,
but who knows...?
Reported-by: Nihal Gabr <gabr.nihal@gmail.com>
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
When dives were merged on import, they were not unregistered
from their dive site and trip before being deleted. Thus, these
tables had stale pointers, which would ultimate lead to crashes.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
This used to be a copy of QSysInfo. However, once the requirement
was raised to Qt5.4, this was replaced by a subclass of the original
QSysInfo - which made the whole file mostly obsolete.
Just use QSysInfo directly where needed.
Only for windows.c, which can't call directly into Qt, keep the
isWin7Or8() helper function.
Signed-off-by: Berthold Stoeger <bstoeger@mail.tuwien.ac.at>
